Designation Requirements—The pipe materials designation code shall consist of the standard designation, ASTM D , followed by type. Home; ASTM D standard by ASTM International, 03/01/ . View all Printed Edition + PDF;; Immediate download; $; Add to Cart. News · SIGN IN / REGISTER. Back. Standards PDF Cover Page Document preview. Historical. ASTM D Content Provider ASTM International [ ASTM].
|Language:||English, Spanish, French|
|ePub File Size:||29.86 MB|
|PDF File Size:||8.49 MB|
|Distribution:||Free* [*Sign up for free]|
D Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Standard + Redline PDF Bundle ASTM License Agreement. This standard is issued under the ﬁxed designation D ; the number immediately Click below to download ASTM D – 04 pdf free. consist of ASTM D three numerals, C and two or and having a minimum pipe stiffness of 9 psi (62 kPa), (2) ASTM D.
Dairg Skip to main content. Learn More — opens in a new window or tab Tda international postage and import charges are paid in part to Pitney Bowes Inc. Tdz Royal Mail International Signed. Sign in for checkout Check out as guest. Back to home tda There are 20 items available.
The composite structure may contain aggregate, granular, or platelet? Thermoplastic or thermosetting liners or coatings may be included. Not a routine quality control test. Table 1 lists the types, liners, grades, classes, and stiffnesses that are covered.
NOTE 3—All possible combinations of types, liners, grades, classes, and stiffnesses may not be commercially available. Additional types, liners, grades, and stiffnesses may be added as they become commercially available. The purchaser should determine for himself or consult with the manufacturer for the proper class, type, liner, grade and stiffness of pipe to be used under the installation and operating conditions that will exist for the project in which the pipe is to be used.
Table 1 presents a summary of the designation requirements. Materials and Manufacture 5.
NOTE 6—Fiberglass pipe intended for use in the transport of potable water should be evaluated and certi? The evaluation should be in accordance with requirements for chemical extraction, taste, and odor that are no less restrictive than those included in National Sanitation Foundation NSF Standard The seal or mark of the laboratory making the evaluation should be included on the?
This cell-type format, however, is subject to misapplication since unobtainable property combinations can be selected if the user is not familiar with non-commercially available products.
The manufacturer should be consulted.
For typical joint detail see Fig. NOTE 7—Other types of joints may be added as they become commercially available. Requirements 6. The pipe shall be as uniform as commercially practicable in color, opacity, density, and other physical properties. No glass? The pipe diameter tolerances shall be as shown in Table 2 or Table 3, when measured in accordance with 8.
The actual laying length shall be the nominal length 62 in. Random lengths, if furnished, shall not vary from the nominal lengths by more than 5 ft 1. For sizes over 54 in. Pressure classes are based on extrapolated strengths at 50 years. For pipe subjected to longitudinal loads or circumferential bending, the effect of these conditions on the hydrostatic design pressure, classi?
At de? NOTE 9—This is a visual observation made with the unaided eye for quality control purposes only and should not be considered a simulated service test.
Table 7 values are based on an in-use long-term de? Tolerance, in. AInside diameters other than those shown shall be permitted by agreement between purchaser and supplier.
BValues are taken from International Standards Organization documents. Parentheses indicate non-preferred diameters.
ToleranceB on Declared ID, mm To avoid possible misapplication, take care to analyze all conditions which might affect performance of the installed pipe. However, minimum values for Level A and Level B de? Restrained rigid joints see 5. For pipe sizes larger than 27 in.
Pipe Equiv. Tolerance, mm? The values may not be indicative of the axial strength of some products, or of the axial strength required by some installation conditions and joint con? Conformance to the requirements of 6.
Sampling 7. Unless otherwise agreed upon between purchaser and supplier, all pipes up to in. Test Methods 8. Lay the tape or gage on or inside the pipe and measure the overall laying length of the pipe. The total indicated reading is equal to twice the distance from a plane perpendicular to the longitudinal axis of the pipe.
Besides, it also shows the global search volume, CPC and the competition for each keyword. The file contains 5 page s and is free to view, download or print.
American Water Works Association.
California Code of Regulations. Department of Public Health of the State of California. Maximum Day Demand.
The actual, estimated or projected amount of water utilized by consumers during the highest day of use, excluding fire flow. Peak Hour Demand. NFPA 13 - Uploaded by. Samir Rabia.
Download with Google Download with Facebook or download with email.